Federation Commander Forum Index Federation Commander
A NEW fast paced board game of starship combat!
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Custom Klingon Cruiser Boom Section??

 
Post new topic   Reply to topic    Federation Commander Forum Index -> Miniatures
View previous topic :: View next topic  
Author Message
OGOPTIMUS
Captain


Joined: 10 Nov 2006
Posts: 980

PostPosted: Mon Feb 09, 2009 9:35 pm    Post subject: Custom Klingon Cruiser Boom Section?? Reply with quote

I'm working on a kitbashed Klingon cruiser, and have (at least some initial) ideas about how to make each part (or buy it) except the boom section.

A simple piece of plastic tubing just seems too simple and kinda lame to me since the boom on all Klingon ships tapers. And I'm not thrilled with covering the thing with green stuff and sanding it down into a roughly conical shape, since that seems like A TON of work for such a small part.

Does anyone have any ideas?
_________________
O.G. OPTIMUS


Newest Page | Newer Page | OLD Page
Back to top
View user's profile Send private message Visit poster's website
djdood
Commodore


Joined: 01 Feb 2007
Posts: 3412
Location: Seattle, WA

PostPosted: Mon Feb 09, 2009 9:48 pm    Post subject: Reply with quote

If it was me (and it might be real soon), I'd buy some brass rod stock, chuck it into a Dremel and hold a file and/or sandpaper to it to get the taper I want. It would be better in a battery-powered (lower speed) Dremel. If the brass is too soft and bends under the pressure of the sanding, I would switch to steel pins.
_________________
Back to top
View user's profile Send private message Send e-mail Visit poster's website
Scoutdad
Commodore


Joined: 09 Oct 2006
Posts: 4754
Location: Middle Tennessee

PostPosted: Mon Feb 09, 2009 10:42 pm    Post subject: Reply with quote

Been there - done that.
The Dremel is what I used - but a multi-speed, electric Dremel set to low speed works even better than a battery operated one does.
_________________
Commander, Battlegroup Murfreesboro
Department Head, ACTASF
Back to top
View user's profile Send private message Send e-mail Yahoo Messenger
djdood
Commodore


Joined: 01 Feb 2007
Posts: 3412
Location: Seattle, WA

PostPosted: Mon Feb 09, 2009 11:23 pm    Post subject: Reply with quote

I like the even-lower RPM's my battery-powered Dremel at low-speed delivers. The plug-in one is over-speed for a lot of delicate things like this.

I intend to do this method for a Romulan JayHawk's third engine. It will be easier to make a new one out of "lathed" brass rod than try to cut and attach one from a Snipe mini.
_________________
Back to top
View user's profile Send private message Send e-mail Visit poster's website
OGOPTIMUS
Captain


Joined: 10 Nov 2006
Posts: 980

PostPosted: Mon Feb 09, 2009 11:44 pm    Post subject: Reply with quote

Thanks for the tips guys. Gotta find a Dremel now. Confused

Then it's on to fabricating the rest of the new ship!

New question now:

Is there a good/better type of file to use for brass than the standard type that I've used for plastic and pewter to this point??
_________________
O.G. OPTIMUS


Newest Page | Newer Page | OLD Page
Back to top
View user's profile Send private message Visit poster's website
Scoutdad
Commodore


Joined: 09 Oct 2006
Posts: 4754
Location: Middle Tennessee

PostPosted: Mon Feb 09, 2009 11:46 pm    Post subject: Reply with quote

My probelm with the battery powered one was always the life of the battery. It never seems to last long enough to even shape a small piece of brass.

Maybe the newer ones (with the lithium-ion batteries) are better, but my old Dremel cordless was always weaker than a $5 box of wine... Shocked
_________________
Commander, Battlegroup Murfreesboro
Department Head, ACTASF
Back to top
View user's profile Send private message Send e-mail Yahoo Messenger
djdood
Commodore


Joined: 01 Feb 2007
Posts: 3412
Location: Seattle, WA

PostPosted: Mon Feb 09, 2009 11:52 pm    Post subject: Reply with quote

Paul/OG - Without knowing what kind of file you are using, it's hard to say. If they are the standard "hobby file", they're steel and they should be fine for both brass and the usual plastic, etc.
_________________
Back to top
View user's profile Send private message Send e-mail Visit poster's website
Scoutdad
Commodore


Joined: 09 Oct 2006
Posts: 4754
Location: Middle Tennessee

PostPosted: Tue Feb 10, 2009 2:54 am    Post subject: Reply with quote

Paul: I've got a selection of "hobby files" I got at the local Hobbytown USA. They didn't have a brand name - but they work just fine on brass, aluminum, epoxy, plastic , etc.

I think they were about $2.99 each and came in various shapes... i.e., round, half round, square, triangular, rectangular, and so on...
_________________
Commander, Battlegroup Murfreesboro
Department Head, ACTASF
Back to top
View user's profile Send private message Send e-mail Yahoo Messenger
OGOPTIMUS
Captain


Joined: 10 Nov 2006
Posts: 980

PostPosted: Tue Feb 10, 2009 7:52 am    Post subject: Reply with quote

OK. I've got a small kit of 12 or so that I got from an ACE Hardware Hobby store. I'll give them a try and see what happens. Gotta get the brass rod now, since all I have at the moment is tubing.

Would plastic be worse for any specific reason? Not as forgiving and easy to flatten?
_________________
O.G. OPTIMUS


Newest Page | Newer Page | OLD Page
Back to top
View user's profile Send private message Visit poster's website
djdood
Commodore


Joined: 01 Feb 2007
Posts: 3412
Location: Seattle, WA

PostPosted: Tue Feb 10, 2009 9:24 am    Post subject: Reply with quote

Plastic will have more tendency to sag, particularly when it heats up from being worked (if you do the Dremel thing). Even still, for a Klingon boom, that bulb on the end will try to make a plastic rod sag.

Nobody is intimidated by a saggy Klingon.
_________________
Back to top
View user's profile Send private message Send e-mail Visit poster's website
Scoutdad
Commodore


Joined: 09 Oct 2006
Posts: 4754
Location: Middle Tennessee

PostPosted: Tue Feb 10, 2009 12:54 pm    Post subject: Reply with quote

djdood wrote:

Nobody is intimidated by a saggy Klingon.

Unless he's carrying a bat'leth and robbing a convenience store...
_________________
Commander, Battlegroup Murfreesboro
Department Head, ACTASF
Back to top
View user's profile Send private message Send e-mail Yahoo Messenger
Display posts from previous:   
Post new topic   Reply to topic    Federation Commander Forum Index -> Miniatures All times are GMT
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group